BMW E82 / E87 / E88 Intake Manifold with Swirl Flap + Actuator

At DDP AutoParts, we provide a high-quality inlet intake manifold assembly with swirl flap actuator motor for BMW models such as the E82, E87, and E88. This part is engineered to restore smooth airflow regulation within your engine, helping the swirl flaps operate precisely as intended. These flaps improve low-end combustion efficiency, but over time they can become clogged, stuck, or mechanically faulty — our replacement manifold and actuator combo helps resolve these issues, reducing fault codes and preventing potential engine damage. Built to OEM-equivalent standards, this unit offers a durable and cost-effective solution over a damaged or deteriorated original manifold.

OEM Number: 11617811214, 11618507240, 11617811215, 11617798885, 11617811300, 11617804744, 11618507239, 11614728712,

Placement on Vehicle : Front

Quantity : 2

Our SKU: TB11618507239-75534SET_94

All our Inlet Intake Manifold With Actuator Motor Swirl Flap For Bmw E82 E87 E88 are OEM quality and reliable after market car parts. This Inlet Intake Manifold With Actuator Motor Swirl Flap For Bmw E82 E87 E88 is specifically compatible with BMW: 1 Series, 3 Series, 5 Series, X1, X3, .

Please use our make-model-year tool to check this part's compatibility with your vehicle. However, please note that our tool is for reference only and we recommend that you check the part number on your old unit prior to purchasing.

If you are still not sure about the compatibility of this part to your vehicle, please supply us with the VIN number or Reg number in our live chat or contact form! You can also find details on our purchasing & shipping guide here.

❓ Frequently Asked Questions 

1. What’s the purpose of the swirl flaps in the intake manifold?
   Swirl flaps are small butterfly-style valves inside the intake manifold that help regulate airflow into the engine. At low engine loads, they create a swirl to improve air-fuel mixing, which aids combustion efficiency and reduces emissions.

2. Why might I need to replace the whole manifold and actuator?

   • Over time, swirl flaps can suffer from carbon buildup, causing them to stick or fail.

   • The actuator’s linkage or motor can wear out, leading to fault codes or poor flap control.

   • In worst-case scenarios, failed flap screws or broken flaps can break off and cause serious engine damage if ingested.

3. Which BMW models / engines is this part compatible with?
   This manifold + actuator combo is designed for BMW 1 Series models (E82, E87, E88) — particularly those with diesel engines (or petrol, depending on manifold spec). It’s compatible with the versions that use swirl flap systems.

4. What are the common symptoms of swirl flap failure?

   • Check engine light with swirl flap fault codes (e.g., “2F8500” or similar).

   • Rattling or “clunk” noises from the intake manifold (especially when the engine revs).

   • Reduced performance or poor low-end response due to mis-regulated airflow.

   • Increasing carbon deposits and build-up inside the manifold.

5. Is it difficult to install / replace the manifold + actuator?

   • Yes, this is a moderately complex repair: you need to remove the existing intake manifold, detach the old actuator, install the new manifold, and reconnect the actuator.

   • After replacement, it’s very important to reset / re-learn the actuator limits using a diagnostic tool, so the new flaps operate correctly.

   • Make sure all gaskets are replaced when doing this job to prevent air leaks.

6. Can I just delete the swirl flaps instead of replacing them?
   Some people do remove the swirl flaps entirely (or “blank” them), but that often requires ECU tuning or a software adaptation.

   • Deleting the flaps can eliminate flap-failure risk, but you may lose some low-end efficiency / torque if not managed properly.

   • Also, the actuator will still try to sweep on ignition unless coded out or physically limited.

7. Will there be any error codes or warning lights after fitting?
   There’s a risk of swirl flap fault codes if the actuator’s “zero position” hasn’t been re-learned, or if the flap mechanism doesn’t move as expected.
   With proper calibration and a good-quality manifold + actuator, most users resolve prior fault codes and prevent future issues.

8. How reliable is this aftermarket replacement?

   • The part is built to OEM-equivalent spec, ensuring good durability and reliable operation.

   • Replacing an old, worn-out manifold/actuator proactively reduces the risk of swirl-flap-related engine damage down the line — a common failure point in these BMW engines.

   • This is a cost-effective preventive / repair solution versus only replacing the motor or dealing with potential catastrophic failure.

9. What warranty or return policy does DDP AutoParts offer?
   We offer our standard parts warranty on this manifold + actuator assembly. If there are any fitment problems, performance issues, or you receive a faulty unit, simply contact our support team — we’ll help you with testing, returns, or a replacement.